Step Instruction for Bathtub Installation
Step Instruction for Bathtub Installation
Blog Article
Are you currently on the lookout for info concerning Installing A Bathtub?
Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is easily obtainable, the job can relocate quickly; if you have to open a wall surface to get rid of the old bathtub and position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the task as well as are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube links.
This post will aid you mount a new bath tub in your washroom if you have already gotten a new bathtub and do not need to transform the arrangement of your previous water supply pipelines.
Your tools and product checklist must comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipes. Once the supply pipelines have been removed, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Before going on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap and also the sink. Protect the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed position. The wooden boards are helpful in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the tub until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the supply of water and also check all joints and new pipework for leakages as well as tighten them if required. Load the bathtub and likewise check the overflow outlet and also the normal outlet for leakages.
Finally, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at least once as this will settle it into its last setting.
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break a rigid seal, causing the water to penetrate the wall surface in between the bath and the tiling, leading to difficulties with moisture as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very inquisitive about Installing A Bathtub and I hope you enjoyed reading the entire entry. Sharing is nice. One never knows, you may be doing someone a favor. Many thanks for your time. Visit again soon.
Need Help? Hire Us Now! Report this page